Study › General › G1C

G1C

COMMISSION'S RULES

- Transmitter power regulations; data emission standards; 60-meter operation requirements

Drill results are kept in this browser. Log in to keep them on your account and get a study plan.

G1C011 of 8§ 97.313(c)(1)

What is the maximum transmitter power an amateur station may use on 10.140 MHz?

Why 10.140 MHz falls in the 30 meter band (10.100 to 10.150 MHz), which FCC rule 97.313(c)(1) caps at 200 watts PEP output for all license classes. The band is a secondary allocation shared with fixed services worldwide, so the low power limit and the CW/data-only restriction help amateurs avoid interfering with primary users.
Watch out 1500 watts PEP is the general Part 97 maximum that applies on most HF bands, but 30 meters is one of the specific exceptions, so the general limit does not apply here.
30 meters is the 'quiet' band: 200 W max, no phone. Remember 10.1 MHz goes with 200 W.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.313(c)(1) Transmitter power standards.

(a) An amateur station must use the minimum transmitter power necessary to carry out the desired communications.

(b) No station may transmit with a transmitter power exceeding 1.5 kW PEP.

(c) No station may transmit with a transmitter power output exceeding 200 W PEP:

(1) On the 10.10-10.15 MHz segment;

(2) On the 3.525-3.60 MHz, 7.025-7.125 MHz, 21.025-21.20 MHz, and 28.0-28.5 MHz segment when the control operator is a Novice Class operator or a Technician Class operator; or

(3) The 7.050-7.075 MHz segment when the station is within ITU Regions 1 or 3.

(d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m band when the control operator is a Novice operator.

(e) No station may transmit with a transmitter power exceeding 5 W PEP on the UHF 23 cm band when the control operator is a Novice operator.

(f) An Earth station or telecommand station may transmit on the 435-438 MHz segment with a maximum of 611 W effective radiated power (1 kW equivalent isotropically radiated power). The transmitting antenna elevation angle between the lower half-power (−3 dB relative to the peak or antenna bore sight) point and the horizon must always be greater than 10°. No other station may transmit with a transmitter power exceeding 50 W PEP on the UHF 70 cm band from an area specified in § 2.106(c)(270)(i) of this chapter, unless expressly authorized by the FCC after mutual agreement, on a case-by-case basis, between the Regional Director of the applicable field facility and the military area frequency coordinator at the applicable military base.

(g) No station may transmit with a transmitter power exceeding 50 W PEP on the 33 cm band from within 241 km of the boundaries of the White Sands Missile Range. Its boundaries are those portions of Texas and New Mexico bounded on the south by latitude 31°41′ North, on the east by longitude 104°11′ West, on the north by latitude 34°30′ North, and on the west by longitude 107°30′ West.

(h) No station may transmit with a transmitter power exceeding 50 W PEP on the 219-220 MHz segment of the 1.25 m band.

(i) 60 m band power requirements: No station may transmit on the frequencies 5.332, 5.348, 5.373, and 5.405 MHz in the 60 m band with a radiated power exceeding 100 W ERP. No station may transmit in the 5.3515-5.3665 MHz band with a radiated power exceeding 9.15 W ERP. For the purpose of computing ERP, the transmitter PEP will be multiplied by the antenna gain relative to a half-wave dipole antenna. A half-wave dipole antenna will be presumed to have a gain of 1 (0 dBd). Licensees using other antennas must maintain in their station records either the antenna manufacturer's data on the antenna gain or calculations of the antenna gain.

(j) No station may transmit with a transmitter output exceeding 10 W PEP when the station is transmitting a SS emission type.

(k) No station may transmit in the 135.7-137.8 kHz (2200 m) band with a transmitter power exceeding 1.5 kW PEP or a radiated power exceeding 1 W EIRP.

(l) No station may transmit in the 472-479 kHz (630 m) band with a transmitter power exceeding 500 W PEP or a radiated power exceeding 5 W EIRP, except that in Alaska, stations located within 800 kilometers of the Russian Federation may not transmit with a radiated power exceeding 1 W EIRP.

(m) No station may transmit with a peak equivalent isotropically radiated power (EIRP) exceeding 316 W in the 76-81 GHz (4 mm) band.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C022 of 8§ 97.313

What is the maximum transmitter power an amateur station may use on the 12-meter band?

Why Section 97.313 sets a general limit of 1500 watts PEP output for amateur stations, and the 12-meter band (24.89-24.99 MHz) has no special reduced-power restriction. Only a few bands carry lower caps, so unless a band is specifically named in the rule, the general 1500 W PEP ceiling applies. Remember that 97.313 also requires you to use the minimum power necessary to carry out the communication, so 1500 W is a ceiling, not a target.
Watch out The 200 watt PEP figure is the special limit for the 30-meter band, and the effective radiated power equivalent to 100 watts from a dipole is the 60-meter channel limit; neither applies on 12 meters.
Only two odd bands: 30 m = 200 W, 60 m = 100 W ERP. Everything else, including 12 m, gets the full 1500 W PEP.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.313 Transmitter power standards.

(a) An amateur station must use the minimum transmitter power necessary to carry out the desired communications.

(b) No station may transmit with a transmitter power exceeding 1.5 kW PEP.

(c) No station may transmit with a transmitter power output exceeding 200 W PEP:

(1) On the 10.10-10.15 MHz segment;

(2) On the 3.525-3.60 MHz, 7.025-7.125 MHz, 21.025-21.20 MHz, and 28.0-28.5 MHz segment when the control operator is a Novice Class operator or a Technician Class operator; or

(3) The 7.050-7.075 MHz segment when the station is within ITU Regions 1 or 3.

(d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m band when the control operator is a Novice operator.

(e) No station may transmit with a transmitter power exceeding 5 W PEP on the UHF 23 cm band when the control operator is a Novice operator.

(f) An Earth station or telecommand station may transmit on the 435-438 MHz segment with a maximum of 611 W effective radiated power (1 kW equivalent isotropically radiated power). The transmitting antenna elevation angle between the lower half-power (−3 dB relative to the peak or antenna bore sight) point and the horizon must always be greater than 10°. No other station may transmit with a transmitter power exceeding 50 W PEP on the UHF 70 cm band from an area specified in § 2.106(c)(270)(i) of this chapter, unless expressly authorized by the FCC after mutual agreement, on a case-by-case basis, between the Regional Director of the applicable field facility and the military area frequency coordinator at the applicable military base.

(g) No station may transmit with a transmitter power exceeding 50 W PEP on the 33 cm band from within 241 km of the boundaries of the White Sands Missile Range. Its boundaries are those portions of Texas and New Mexico bounded on the south by latitude 31°41′ North, on the east by longitude 104°11′ West, on the north by latitude 34°30′ North, and on the west by longitude 107°30′ West.

(h) No station may transmit with a transmitter power exceeding 50 W PEP on the 219-220 MHz segment of the 1.25 m band.

(i) 60 m band power requirements: No station may transmit on the frequencies 5.332, 5.348, 5.373, and 5.405 MHz in the 60 m band with a radiated power exceeding 100 W ERP. No station may transmit in the 5.3515-5.3665 MHz band with a radiated power exceeding 9.15 W ERP. For the purpose of computing ERP, the transmitter PEP will be multiplied by the antenna gain relative to a half-wave dipole antenna. A half-wave dipole antenna will be presumed to have a gain of 1 (0 dBd). Licensees using other antennas must maintain in their station records either the antenna manufacturer's data on the antenna gain or calculations of the antenna gain.

(j) No station may transmit with a transmitter output exceeding 10 W PEP when the station is transmitting a SS emission type.

(k) No station may transmit in the 135.7-137.8 kHz (2200 m) band with a transmitter power exceeding 1.5 kW PEP or a radiated power exceeding 1 W EIRP.

(l) No station may transmit in the 472-479 kHz (630 m) band with a transmitter power exceeding 500 W PEP or a radiated power exceeding 5 W EIRP, except that in Alaska, stations located within 800 kilometers of the Russian Federation may not transmit with a radiated power exceeding 1 W EIRP.

(m) No station may transmit with a peak equivalent isotropically radiated power (EIRP) exceeding 316 W in the 76-81 GHz (4 mm) band.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C033 of 8§ 97.303(h)(1)

What is the maximum bandwidth permitted by FCC rules for amateur radio stations transmitting on USB frequencies in the 60-meter band?

Why The 60-meter band is a channelized, secondary allocation shared with federal users, so the FCC set tight limits in 97.303(h). Amateurs must use upper sideband on the five channels, and the occupied bandwidth of any emission there may not exceed 2.8 kHz, centered on the channel center frequency. That figure is a bit narrower than a typical HF SSB signal, so transmitters should be set for a clean, standard voice bandwidth rather than an extended-audio setting.
Watch out The 3 kHz figure is tempting because it is the usual rule-of-thumb width of an SSB phone signal and appears in other parts of the rules, but 60 meters specifically caps it at 2.8 kHz.
60 meters: USB only, 2.8 kHz max. Think "2.8 on 5 channels."
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.303(h)(1) Frequency sharing requirements.

The following paragraphs summarize the frequency sharing requirements that apply to amateur stations transmitting in the frequency bands specified in § 97.301 of this part. Each frequency band allocated to the amateur service is designated as either a secondary service or a primary service. A station in a secondary service must not cause harmful interference to, and must accept interference from, stations in a primary service.

(a) Where, in adjacent ITU Regions or sub-Regions, a band of frequencies is allocated to different services of the same category (i.e., primary or secondary services), the basic principle is the equality of right to operate. Accordingly, stations of each service in one Region or sub-Region must operate so as not to cause harmful interference to any service of the same or higher category in the other Regions or sub-Regions.

(b) Amateur stations transmitting in the 70 cm band, the 33 cm band, the 23 cm band, the 5 cm band, the 3 cm band, or the 24.05-24.25 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the United States Government in the radiolocation service.

(c) Amateur stations transmitting in the 76-81 GHz segment, the 136-141 GHz segment, or the 241-248 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the United States Government, the FCC, or other nations in the radiolocation service.

(d) Amateur stations transmitting in the 430-450 MHz segment, the 23 cm band, the 3.3-3.4 GHz segment, the 5.65-5.85 GHz segment, the 13 cm band, or the 24.05-24.25 GHz segment, must not cause harmful interference to, and must accept interference from, stations authorized by other nations in the radiolocation service.

(e) Amateur stations receiving in the 33 cm band, the 2400-2450 MHz segment, the 5.725-5.875 GHz segment, the 1.2 cm band, the 2.5 mm band, or the 244-246 GHz segment must accept interference from industrial, scientific, and medical (ISM) equipment.

(f) Amateur stations transmitting in the following segments must not cause harmful interference to radio astronomy stations: 76-81 GHz, 136-141 GHz, 241-248 GHz, 275-323 GHz, 327-371 GHz, 388-424 GHz, 426-442 GHz, 453-510 GHz, 623-711 GHz, 795-909 GHz, or 926-945 GHz. In addition, amateur stations transmitting in the following segments must not cause harmful interference to stations in the Earth exploration-satellite service (passive) or the space research service (passive): 275-286 GHz, 296-306 GHz, 313-356 GHz, 361-365 GHz, 369-392 GHz, 397-399 GHz, 409-411 GHz, 416-434 GHz, 439-467 GHz, 477-502 GHz, 523-527 GHz, 538-581 GHz, 611-630 GHz, 634-654 GHz, 657-692 GHz, 713-718 GHz, 729-733 GHz, 750-754 GHz, 771-776 GHz, 823-846 GHz, 850-854 GHz, 857-862 GHz, 866-882 GHz, 905-928 GHz, 951-956 GHz, 968-973 GHz and 985-990 GHz.

(g) In the 2200 m and 630 m bands:

(1) Amateur stations in the 135.7-137.8 kHz (2200 m) and 472-479 kHz (630 m) bands shall only operate at fixed locations. Amateur stations shall not operate within a horizontal distance of one kilometer from a transmission line that conducts a power line carrier (PLC) signal in the 135.7-137.8 kHz or 472-479 kHz bands. Horizontal distance is measured from the station's antenna to the closest point on the transmission line.

(2) Prior to commencement of operations in the 135.7-137.8 kHz (2200 m) and/or 472-479 kHz (630 m) bands, amateur operators shall notify the Utilities Telecom Council (UTC) of their intent to operate by submitting their call signs, intended band or bands of operation, and the coordinates of their antenna's fixed location. Amateur stations will be permitted to commence operations after the 30-day period unless UTC notifies the station that its fixed location is located within one kilometer of PLC systems operating in the same or overlapping frequencies.

(3) Amateur stations in the 135.7-137.8 kHz (2200 m) band shall not cause harmful interference to, and shall accept interference from:

(i) Stations authorized by the United States Government in the fixed and maritime mobile services;

(ii) Stations authorized by other nations in the fixed, maritime mobile, and radionavigation service.

(4) Amateur stations in the 472-479 kHz (630 m) band shall not cause harmful interference to, and shall accept interference from:

(i) Stations authorized by the FCC in the maritime mobile service;

(ii) Stations authorized by other nations in the maritime mobile and aeronautical radionavigation services.

(5) Amateur stations causing harmful interference shall take all necessary measures to eliminate such interference—including temporary or permanent termination of transmissions.

(h) Amateur stations transmitting on frequencies in the 60 m band must not cause harmful interference to, and must accept interference from, stations authorized by:

(1) The United States (NTIA and FCC) and other nations in the fixed service; and

(2) Other nations in the mobile except aeronautical mobile service.

(3) In the 5330.5-5406.4 kHz band (60 m band), amateur stations may transmit only in the 5351.5-5366.5 kHz band and on the four center frequencies specified in the table below. For the discrete channels, control operators of stations transmitting phone, data, and RTTY emissions (emission designators 2K80J3E, 2K80J2D, and 60H0J2B, respectively) may set the carrier frequency 1.5 kHz below the center frequency as specified in the table below. For CW emissions (emission designator 150HA1A), the carrier frequency is set to the center frequency. For all 60 m spectrum, Amateur operators shall ensure that their emissions do not occupy more than 2.8 kHz.

(i) Amateur stations transmitting in the 7.2-7.3 MHz segment must not cause harmful interference to, and must accept interference from, international broadcast stations whose programming is intended for use within Region 1 or Region 3.

(j) Amateur stations transmitting in the 30 m band must not cause harmful interference to, and must accept interference from, stations by other nations in the fixed service. The licensee of the amateur station must make all necessary adjustments, including termination of transmissions, if harmful interference is caused.

(k) For amateur stations located in ITU Regions 1 and 3: Amateur stations transmitting in the 146-148 MHz segment or the 10.00-10.45 GHz segment must not cause harmful interference to, and must accept interference from, stations of other nations in the fixed and mobile services.

(l) In the 219-220 MHz segment:

(1) Use is restricted to amateur stations participating as forwarding stations in fixed point-to-point digital message forwarding systems, including intercity packet backbone networks. It is not available for other purposes.

(2) Amateur stations must not cause harmful interference to, and must accept interference from, stations authorized by:

(i) The FCC in the Automated Maritime Telecommunications System (AMTS), the 218-219 MHz Service, and the 220 MHz Service, and television stations broadcasting on channels 11 and 13; and

(ii) Other nations in the fixed and maritime mobile services.

(3) No amateur station may transmit unless the licensee has given written notification of the station's specific geographic location for such transmissions in order to be incorporated into a database that has been made available to the public. The notification must be given at least 30 days prior to making such transmissions. The notification must be given to: The American Radio Relay League, Inc., 225 Main Street, Newington, CT 06111-1494.

(4) No amateur station may transmit from a location that is within 640 km of an AMTS coast station that operates in the 217-218 MHz and 219-220 MHz bands unless the amateur station licensee has given written notification of the station's specific geographic location for such transmissions to the AMTS licensee. The notification must be given at least 30 days prior to making such transmissions. The location of AMTS coast stations using the 217-218/219-220 MHz channels may be obtained as noted in paragraph (l)(3) of this section.

(5) No amateur station may transmit from a location that is within 80 km of an AMTS coast station that uses frequencies in the 217-218 MHz and 219-220 MHz bands unless that amateur station licensee holds written approval from that AMTS licensee. The location of AMTS coast stations using the 217-218/219-220 MHz channels may be obtained as noted in paragraph (l)(3) of this section.

(m) In the 70 cm band:

(1) No amateur station shall transmit from north of Line A in the 420-430 MHz segment. See § 97.3(a) for the definition of Line A.

(2) Amateur stations transmitting in the 420-430 MHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the FCC in the land mobile service within 80.5 km of Buffalo, Cleveland, and Detroit. See § 2.106, footnote US230 for specific frequencies and coordinates.

(3) Amateur stations transmitting in the 420-430 MHz segment or the 440-450 MHz segment must not cause harmful interference to, and must accept interference from, stations authorized by other nations in the fixed and mobile except aeronautical mobile services.

(n) In the 33 cm band:

(1) Amateur stations must not cause harmful interference to, and must accept interference from, stations authorized by:

(i) The United States Government;

(ii) The FCC in the Location and Monitoring Service; and

(iii) Other nations in the fixed service.

(2) No amateur station shall transmit from those portions of Texas and New Mexico that are bounded by latitudes 31°41′ and 34°30′ North and longitudes 104°11′ and 107°30′ West; or from outside of the United States and its Region 2 insular areas.

(3) No amateur station shall transmit from those portions of Colorado and Wyoming that are bounded by latitudes 39° and 42° North and longitudes 103° and 108° West in the following segments: 902.4-902.6 MHz, 904.3-904.7 MHz, 925.3-925.7 MHz, and 927.3-927.7 MHz.

(o) Amateur stations transmitting in the 23 cm band must not cause harmful interference to, and must accept interference from, stations authorized by:

(1) The United States Government in the aeronautical radionavigation, Earth exploration-satellite (active), or space research (active) services;

(2) The FCC in the aeronautical radionavigation service; and

(3) Other nations in the Earth exploration-satellite (active), radionavigation-satellite (space-to-Earth) (space-to-space), or space research (active) services.

(p) In the 13 cm band:

(1) Amateur stations must not cause harmful interference to, and must accept interference from, stations authorized by other nations in fixed and mobile services.

(2) Amateur stations transmitting in the 2305-2310 MHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the FCC in the fixed, mobile except aeronautical mobile, and radiolocation services.

(q) [Reserved]

(r) In the 5 cm band:

(1) Amateur stations transmitting in the 5.650-5.725 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by other nations in the mobile except aeronautical mobile service.

(2) Amateur stations transmitting in the 5.850-5.925 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the FCC and other nations in the fixed-satellite (Earth-to-space) and mobile services and also stations authorized by other nations in the fixed service. In the United States, the use of mobile service is restricted to operations in the Intelligent Transportation System radio service.

(s) [Reserved]

(t) Amateur stations transmitting in the 2.5 mm band must not cause harmful interference to, and must accept interference from, stations authorized by the United States Government, the FCC, or other nations in the fixed, inter-satellite, or mobile services.

The Table of Frequency Allocations contains the complete, unabridged, and legally binding frequency sharing requirements that pertain to the Amateur Radio Service. See 47 CFR 2.104, 2.105, and 2.106. The United States, Puerto Rico, and the U.S. Virgin Islands are in Region 2 and other U.S. insular areas are in either Region 2 or 3; see appendix 1 to part 97.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C044 of 8§ 97.303(i)

Which of the following is required by the FCC rules when operating in the 60-meter band?

Why On 60 meters the power limit is stated as effective radiated power relative to a half-wave dipole, currently 100 W PEP ERP. To prove you are within that limit with any other antenna, 97.303(i) requires you to keep a record of your antenna's gain so the ERP can be calculated from your transmitter output. A dipole needs no record because it is the reference antenna itself.
Watch out Logging date, time, frequency, power and stations worked was once required of all amateurs decades ago but is not required today, on 60 meters or anywhere else; the only 60-meter record keeping rule concerns antenna gain.
60 m limit is ERP referenced to a dipole, so if your antenna isn't a dipole, write down its gain.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.303(i) Frequency sharing requirements.

The following paragraphs summarize the frequency sharing requirements that apply to amateur stations transmitting in the frequency bands specified in § 97.301 of this part. Each frequency band allocated to the amateur service is designated as either a secondary service or a primary service. A station in a secondary service must not cause harmful interference to, and must accept interference from, stations in a primary service.

(a) Where, in adjacent ITU Regions or sub-Regions, a band of frequencies is allocated to different services of the same category (i.e., primary or secondary services), the basic principle is the equality of right to operate. Accordingly, stations of each service in one Region or sub-Region must operate so as not to cause harmful interference to any service of the same or higher category in the other Regions or sub-Regions.

(b) Amateur stations transmitting in the 70 cm band, the 33 cm band, the 23 cm band, the 5 cm band, the 3 cm band, or the 24.05-24.25 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the United States Government in the radiolocation service.

(c) Amateur stations transmitting in the 76-81 GHz segment, the 136-141 GHz segment, or the 241-248 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the United States Government, the FCC, or other nations in the radiolocation service.

(d) Amateur stations transmitting in the 430-450 MHz segment, the 23 cm band, the 3.3-3.4 GHz segment, the 5.65-5.85 GHz segment, the 13 cm band, or the 24.05-24.25 GHz segment, must not cause harmful interference to, and must accept interference from, stations authorized by other nations in the radiolocation service.

(e) Amateur stations receiving in the 33 cm band, the 2400-2450 MHz segment, the 5.725-5.875 GHz segment, the 1.2 cm band, the 2.5 mm band, or the 244-246 GHz segment must accept interference from industrial, scientific, and medical (ISM) equipment.

(f) Amateur stations transmitting in the following segments must not cause harmful interference to radio astronomy stations: 76-81 GHz, 136-141 GHz, 241-248 GHz, 275-323 GHz, 327-371 GHz, 388-424 GHz, 426-442 GHz, 453-510 GHz, 623-711 GHz, 795-909 GHz, or 926-945 GHz. In addition, amateur stations transmitting in the following segments must not cause harmful interference to stations in the Earth exploration-satellite service (passive) or the space research service (passive): 275-286 GHz, 296-306 GHz, 313-356 GHz, 361-365 GHz, 369-392 GHz, 397-399 GHz, 409-411 GHz, 416-434 GHz, 439-467 GHz, 477-502 GHz, 523-527 GHz, 538-581 GHz, 611-630 GHz, 634-654 GHz, 657-692 GHz, 713-718 GHz, 729-733 GHz, 750-754 GHz, 771-776 GHz, 823-846 GHz, 850-854 GHz, 857-862 GHz, 866-882 GHz, 905-928 GHz, 951-956 GHz, 968-973 GHz and 985-990 GHz.

(g) In the 2200 m and 630 m bands:

(1) Amateur stations in the 135.7-137.8 kHz (2200 m) and 472-479 kHz (630 m) bands shall only operate at fixed locations. Amateur stations shall not operate within a horizontal distance of one kilometer from a transmission line that conducts a power line carrier (PLC) signal in the 135.7-137.8 kHz or 472-479 kHz bands. Horizontal distance is measured from the station's antenna to the closest point on the transmission line.

(2) Prior to commencement of operations in the 135.7-137.8 kHz (2200 m) and/or 472-479 kHz (630 m) bands, amateur operators shall notify the Utilities Telecom Council (UTC) of their intent to operate by submitting their call signs, intended band or bands of operation, and the coordinates of their antenna's fixed location. Amateur stations will be permitted to commence operations after the 30-day period unless UTC notifies the station that its fixed location is located within one kilometer of PLC systems operating in the same or overlapping frequencies.

(3) Amateur stations in the 135.7-137.8 kHz (2200 m) band shall not cause harmful interference to, and shall accept interference from:

(i) Stations authorized by the United States Government in the fixed and maritime mobile services;

(ii) Stations authorized by other nations in the fixed, maritime mobile, and radionavigation service.

(4) Amateur stations in the 472-479 kHz (630 m) band shall not cause harmful interference to, and shall accept interference from:

(i) Stations authorized by the FCC in the maritime mobile service;

(ii) Stations authorized by other nations in the maritime mobile and aeronautical radionavigation services.

(5) Amateur stations causing harmful interference shall take all necessary measures to eliminate such interference—including temporary or permanent termination of transmissions.

(h) Amateur stations transmitting on frequencies in the 60 m band must not cause harmful interference to, and must accept interference from, stations authorized by:

(1) The United States (NTIA and FCC) and other nations in the fixed service; and

(2) Other nations in the mobile except aeronautical mobile service.

(3) In the 5330.5-5406.4 kHz band (60 m band), amateur stations may transmit only in the 5351.5-5366.5 kHz band and on the four center frequencies specified in the table below. For the discrete channels, control operators of stations transmitting phone, data, and RTTY emissions (emission designators 2K80J3E, 2K80J2D, and 60H0J2B, respectively) may set the carrier frequency 1.5 kHz below the center frequency as specified in the table below. For CW emissions (emission designator 150HA1A), the carrier frequency is set to the center frequency. For all 60 m spectrum, Amateur operators shall ensure that their emissions do not occupy more than 2.8 kHz.

(i) Amateur stations transmitting in the 7.2-7.3 MHz segment must not cause harmful interference to, and must accept interference from, international broadcast stations whose programming is intended for use within Region 1 or Region 3.

(j) Amateur stations transmitting in the 30 m band must not cause harmful interference to, and must accept interference from, stations by other nations in the fixed service. The licensee of the amateur station must make all necessary adjustments, including termination of transmissions, if harmful interference is caused.

(k) For amateur stations located in ITU Regions 1 and 3: Amateur stations transmitting in the 146-148 MHz segment or the 10.00-10.45 GHz segment must not cause harmful interference to, and must accept interference from, stations of other nations in the fixed and mobile services.

(l) In the 219-220 MHz segment:

(1) Use is restricted to amateur stations participating as forwarding stations in fixed point-to-point digital message forwarding systems, including intercity packet backbone networks. It is not available for other purposes.

(2) Amateur stations must not cause harmful interference to, and must accept interference from, stations authorized by:

(i) The FCC in the Automated Maritime Telecommunications System (AMTS), the 218-219 MHz Service, and the 220 MHz Service, and television stations broadcasting on channels 11 and 13; and

(ii) Other nations in the fixed and maritime mobile services.

(3) No amateur station may transmit unless the licensee has given written notification of the station's specific geographic location for such transmissions in order to be incorporated into a database that has been made available to the public. The notification must be given at least 30 days prior to making such transmissions. The notification must be given to: The American Radio Relay League, Inc., 225 Main Street, Newington, CT 06111-1494.

(4) No amateur station may transmit from a location that is within 640 km of an AMTS coast station that operates in the 217-218 MHz and 219-220 MHz bands unless the amateur station licensee has given written notification of the station's specific geographic location for such transmissions to the AMTS licensee. The notification must be given at least 30 days prior to making such transmissions. The location of AMTS coast stations using the 217-218/219-220 MHz channels may be obtained as noted in paragraph (l)(3) of this section.

(5) No amateur station may transmit from a location that is within 80 km of an AMTS coast station that uses frequencies in the 217-218 MHz and 219-220 MHz bands unless that amateur station licensee holds written approval from that AMTS licensee. The location of AMTS coast stations using the 217-218/219-220 MHz channels may be obtained as noted in paragraph (l)(3) of this section.

(m) In the 70 cm band:

(1) No amateur station shall transmit from north of Line A in the 420-430 MHz segment. See § 97.3(a) for the definition of Line A.

(2) Amateur stations transmitting in the 420-430 MHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the FCC in the land mobile service within 80.5 km of Buffalo, Cleveland, and Detroit. See § 2.106, footnote US230 for specific frequencies and coordinates.

(3) Amateur stations transmitting in the 420-430 MHz segment or the 440-450 MHz segment must not cause harmful interference to, and must accept interference from, stations authorized by other nations in the fixed and mobile except aeronautical mobile services.

(n) In the 33 cm band:

(1) Amateur stations must not cause harmful interference to, and must accept interference from, stations authorized by:

(i) The United States Government;

(ii) The FCC in the Location and Monitoring Service; and

(iii) Other nations in the fixed service.

(2) No amateur station shall transmit from those portions of Texas and New Mexico that are bounded by latitudes 31°41′ and 34°30′ North and longitudes 104°11′ and 107°30′ West; or from outside of the United States and its Region 2 insular areas.

(3) No amateur station shall transmit from those portions of Colorado and Wyoming that are bounded by latitudes 39° and 42° North and longitudes 103° and 108° West in the following segments: 902.4-902.6 MHz, 904.3-904.7 MHz, 925.3-925.7 MHz, and 927.3-927.7 MHz.

(o) Amateur stations transmitting in the 23 cm band must not cause harmful interference to, and must accept interference from, stations authorized by:

(1) The United States Government in the aeronautical radionavigation, Earth exploration-satellite (active), or space research (active) services;

(2) The FCC in the aeronautical radionavigation service; and

(3) Other nations in the Earth exploration-satellite (active), radionavigation-satellite (space-to-Earth) (space-to-space), or space research (active) services.

(p) In the 13 cm band:

(1) Amateur stations must not cause harmful interference to, and must accept interference from, stations authorized by other nations in fixed and mobile services.

(2) Amateur stations transmitting in the 2305-2310 MHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the FCC in the fixed, mobile except aeronautical mobile, and radiolocation services.

(q) [Reserved]

(r) In the 5 cm band:

(1) Amateur stations transmitting in the 5.650-5.725 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by other nations in the mobile except aeronautical mobile service.

(2) Amateur stations transmitting in the 5.850-5.925 GHz segment must not cause harmful interference to, and must accept interference from, stations authorized by the FCC and other nations in the fixed-satellite (Earth-to-space) and mobile services and also stations authorized by other nations in the fixed service. In the United States, the use of mobile service is restricted to operations in the Intelligent Transportation System radio service.

(s) [Reserved]

(t) Amateur stations transmitting in the 2.5 mm band must not cause harmful interference to, and must accept interference from, stations authorized by the United States Government, the FCC, or other nations in the fixed, inter-satellite, or mobile services.

The Table of Frequency Allocations contains the complete, unabridged, and legally binding frequency sharing requirements that pertain to the Amateur Radio Service. See 47 CFR 2.104, 2.105, and 2.106. The United States, Puerto Rico, and the U.S. Virgin Islands are in Region 2 and other U.S. insular areas are in either Region 2 or 3; see appendix 1 to part 97.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C055 of 8§ 97.313

What is the limit for transmitter power on the 28 MHz band for a General Class control operator?

Why Section 97.313(b) sets the general amateur power ceiling at 1500 watts PEP output, and that applies to Generals on 10 meters. The lower limits carved out elsewhere in 97.313 cover specific cases: 200 watts PEP on 30 meters and in the old Novice/Technician HF segments, and the 60-meter effective radiated power limit. Since 28 MHz has no such special restriction for General licensees, the full legal limit applies. Remember the rule always says use the minimum power necessary, so 1500 watts is a ceiling, not a target.
Watch out The choice that says 100 watts is just the typical output of a barefoot transceiver, not a legal limit, and the 200-watt figure people often recall for 10 meters applies to Novice and Technician operators in 28.0-28.5 MHz, not to Generals.
1500 W PEP is the default everywhere; the exceptions to memorize are 200 W on 30 m and the 60 m ERP rule.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.313 Transmitter power standards.

(a) An amateur station must use the minimum transmitter power necessary to carry out the desired communications.

(b) No station may transmit with a transmitter power exceeding 1.5 kW PEP.

(c) No station may transmit with a transmitter power output exceeding 200 W PEP:

(1) On the 10.10-10.15 MHz segment;

(2) On the 3.525-3.60 MHz, 7.025-7.125 MHz, 21.025-21.20 MHz, and 28.0-28.5 MHz segment when the control operator is a Novice Class operator or a Technician Class operator; or

(3) The 7.050-7.075 MHz segment when the station is within ITU Regions 1 or 3.

(d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m band when the control operator is a Novice operator.

(e) No station may transmit with a transmitter power exceeding 5 W PEP on the UHF 23 cm band when the control operator is a Novice operator.

(f) An Earth station or telecommand station may transmit on the 435-438 MHz segment with a maximum of 611 W effective radiated power (1 kW equivalent isotropically radiated power). The transmitting antenna elevation angle between the lower half-power (−3 dB relative to the peak or antenna bore sight) point and the horizon must always be greater than 10°. No other station may transmit with a transmitter power exceeding 50 W PEP on the UHF 70 cm band from an area specified in § 2.106(c)(270)(i) of this chapter, unless expressly authorized by the FCC after mutual agreement, on a case-by-case basis, between the Regional Director of the applicable field facility and the military area frequency coordinator at the applicable military base.

(g) No station may transmit with a transmitter power exceeding 50 W PEP on the 33 cm band from within 241 km of the boundaries of the White Sands Missile Range. Its boundaries are those portions of Texas and New Mexico bounded on the south by latitude 31°41′ North, on the east by longitude 104°11′ West, on the north by latitude 34°30′ North, and on the west by longitude 107°30′ West.

(h) No station may transmit with a transmitter power exceeding 50 W PEP on the 219-220 MHz segment of the 1.25 m band.

(i) 60 m band power requirements: No station may transmit on the frequencies 5.332, 5.348, 5.373, and 5.405 MHz in the 60 m band with a radiated power exceeding 100 W ERP. No station may transmit in the 5.3515-5.3665 MHz band with a radiated power exceeding 9.15 W ERP. For the purpose of computing ERP, the transmitter PEP will be multiplied by the antenna gain relative to a half-wave dipole antenna. A half-wave dipole antenna will be presumed to have a gain of 1 (0 dBd). Licensees using other antennas must maintain in their station records either the antenna manufacturer's data on the antenna gain or calculations of the antenna gain.

(j) No station may transmit with a transmitter output exceeding 10 W PEP when the station is transmitting a SS emission type.

(k) No station may transmit in the 135.7-137.8 kHz (2200 m) band with a transmitter power exceeding 1.5 kW PEP or a radiated power exceeding 1 W EIRP.

(l) No station may transmit in the 472-479 kHz (630 m) band with a transmitter power exceeding 500 W PEP or a radiated power exceeding 5 W EIRP, except that in Alaska, stations located within 800 kilometers of the Russian Federation may not transmit with a radiated power exceeding 1 W EIRP.

(m) No station may transmit with a peak equivalent isotropically radiated power (EIRP) exceeding 316 W in the 76-81 GHz (4 mm) band.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C066 of 8§ 97.313

What is the limit for transmitter power on the 1.8 MHz band?

Why Section 97.313 sets a general maximum of 1500 watts PEP output for amateur stations, and the 1.8 MHz (160 meter) band gets that full limit with no special reduction. The only bands with lower caps are 30 meters (200 watts PEP), the 60 meter channels (100 watts PEP effective radiated power relative to a dipole), and certain segments restricted for Novice/Technician operators. As always, 97.313(a) still requires using the minimum power necessary to carry out the communication.
Watch out The 200 watt figure belongs to the 30 meter band (10.1 MHz), not 160 meters; older rules once limited 1.8 MHz power, but that restriction no longer exists.
1500 W PEP is the default everywhere; the exceptions to memorize are 200 W on 30 m and 100 W ERP on 60 m.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.313 Transmitter power standards.

(a) An amateur station must use the minimum transmitter power necessary to carry out the desired communications.

(b) No station may transmit with a transmitter power exceeding 1.5 kW PEP.

(c) No station may transmit with a transmitter power output exceeding 200 W PEP:

(1) On the 10.10-10.15 MHz segment;

(2) On the 3.525-3.60 MHz, 7.025-7.125 MHz, 21.025-21.20 MHz, and 28.0-28.5 MHz segment when the control operator is a Novice Class operator or a Technician Class operator; or

(3) The 7.050-7.075 MHz segment when the station is within ITU Regions 1 or 3.

(d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m band when the control operator is a Novice operator.

(e) No station may transmit with a transmitter power exceeding 5 W PEP on the UHF 23 cm band when the control operator is a Novice operator.

(f) An Earth station or telecommand station may transmit on the 435-438 MHz segment with a maximum of 611 W effective radiated power (1 kW equivalent isotropically radiated power). The transmitting antenna elevation angle between the lower half-power (−3 dB relative to the peak or antenna bore sight) point and the horizon must always be greater than 10°. No other station may transmit with a transmitter power exceeding 50 W PEP on the UHF 70 cm band from an area specified in § 2.106(c)(270)(i) of this chapter, unless expressly authorized by the FCC after mutual agreement, on a case-by-case basis, between the Regional Director of the applicable field facility and the military area frequency coordinator at the applicable military base.

(g) No station may transmit with a transmitter power exceeding 50 W PEP on the 33 cm band from within 241 km of the boundaries of the White Sands Missile Range. Its boundaries are those portions of Texas and New Mexico bounded on the south by latitude 31°41′ North, on the east by longitude 104°11′ West, on the north by latitude 34°30′ North, and on the west by longitude 107°30′ West.

(h) No station may transmit with a transmitter power exceeding 50 W PEP on the 219-220 MHz segment of the 1.25 m band.

(i) 60 m band power requirements: No station may transmit on the frequencies 5.332, 5.348, 5.373, and 5.405 MHz in the 60 m band with a radiated power exceeding 100 W ERP. No station may transmit in the 5.3515-5.3665 MHz band with a radiated power exceeding 9.15 W ERP. For the purpose of computing ERP, the transmitter PEP will be multiplied by the antenna gain relative to a half-wave dipole antenna. A half-wave dipole antenna will be presumed to have a gain of 1 (0 dBd). Licensees using other antennas must maintain in their station records either the antenna manufacturer's data on the antenna gain or calculations of the antenna gain.

(j) No station may transmit with a transmitter output exceeding 10 W PEP when the station is transmitting a SS emission type.

(k) No station may transmit in the 135.7-137.8 kHz (2200 m) band with a transmitter power exceeding 1.5 kW PEP or a radiated power exceeding 1 W EIRP.

(l) No station may transmit in the 472-479 kHz (630 m) band with a transmitter power exceeding 500 W PEP or a radiated power exceeding 5 W EIRP, except that in Alaska, stations located within 800 kilometers of the Russian Federation may not transmit with a radiated power exceeding 1 W EIRP.

(m) No station may transmit with a peak equivalent isotropically radiated power (EIRP) exceeding 316 W in the 76-81 GHz (4 mm) band.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C077 of 8§ 97.309(a)(4)

What must be done before using a new digital protocol on the air?

Why Section 97.309(a)(4) permits amateurs to use digital codes other than the ones specifically listed in the rules, but only if the technical characteristics of the code have been publicly documented. The point is that amateur transmissions may never be obscured: anyone monitoring must be able to find the specification and decode what they hear. So a new protocol becomes legal the moment its details are published, with no FCC paperwork involved.
Watch out Filing a rule-making petition or getting an experimental license sounds official, but the FCC deliberately left this open so hams can innovate without asking permission; type certification applies to manufactured equipment in other services, not to amateur-developed protocols.
Publish, don't petition. If the spec is public, the code is legal; secret codes are prohibited obscured communications.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.309(a)(4) RTTY and data emission codes.

(a) Where authorized by §§ 97.305(c) and 97.307(f) of the part, an amateur station may transmit a RTTY or data emission using the following specified digital codes:

(1) The 5-unit, start-stop, International Telegraph Alphabet No. 2, code defined in ITU-T Recommendation F.1, Division C (commonly known as “Baudot”).

(2) The 7-unit code specified in ITU-R Recommendations M.476-5 and M.625-3 (commonly known as “AMTOR”).

(3) The 7-unit, International Alphabet No. 5, code defined in IT--T Recommendation T.50 (commonly known as “ASCII”).

(4) An amateur station transmitting a RTTY or data emission using a digital code specified in this paragraph may use any technique whose technical characteristics have been documented publicly, such as CLOVER, G-TOR, or PacTOR, for the purpose of facilitating communications.

(b) Where authorized by §§ 97.305(c) and 97.307(f), a station may transmit a RTTY or data emission using an unspecified digital code, except to a station in a country with which the United States does not have an agreement permitting the code to be used. RTTY and data emissions using unspecified digital codes must not be transmitted for the purpose of obscuring the meaning of any communication. When deemed necessary by a Regional Director to assure compliance with the FCC Rules, a station must:

(1) Cease the transmission using the unspecified digital code;

(2) Restrict transmissions of any digital code to the extent instructed;

(3) Maintain a record, convertible to the original information, of all digital communications transmitted.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
G1C118 of 8§ 97.313

What measurement is specified by FCC rules that regulate maximum power?

Why Section 97.313 states amateur power limits in terms of peak envelope power (PEP) output from the transmitter, not input power to the tubes or antenna. PEP is the average power during one RF cycle at the crest of the modulation envelope, which is the meaningful measure for SSB and other varying-envelope modes. The general limit is 1500 W PEP output, with lower limits in certain bands and for certain license classes. (The 60-meter channels are a special case, specified as effective radiated power relative to a dipole.)
Watch out The choices mentioning input power describe the old pre-1990 rule based on DC input to the final amplifier, which the FCC abandoned; RMS output is not how Part 97 states the limit either.
Power rules: PEP OUT of the transmitter, 1500 W max. Not input, not RMS.
HamSandwich explanation, first draft. The question and answers are the NCVEC text.
47 CFR 97.313 Transmitter power standards.

(a) An amateur station must use the minimum transmitter power necessary to carry out the desired communications.

(b) No station may transmit with a transmitter power exceeding 1.5 kW PEP.

(c) No station may transmit with a transmitter power output exceeding 200 W PEP:

(1) On the 10.10-10.15 MHz segment;

(2) On the 3.525-3.60 MHz, 7.025-7.125 MHz, 21.025-21.20 MHz, and 28.0-28.5 MHz segment when the control operator is a Novice Class operator or a Technician Class operator; or

(3) The 7.050-7.075 MHz segment when the station is within ITU Regions 1 or 3.

(d) No station may transmit with a transmitter power exceeding 25 W PEP on the VHF 1.25 m band when the control operator is a Novice operator.

(e) No station may transmit with a transmitter power exceeding 5 W PEP on the UHF 23 cm band when the control operator is a Novice operator.

(f) An Earth station or telecommand station may transmit on the 435-438 MHz segment with a maximum of 611 W effective radiated power (1 kW equivalent isotropically radiated power). The transmitting antenna elevation angle between the lower half-power (−3 dB relative to the peak or antenna bore sight) point and the horizon must always be greater than 10°. No other station may transmit with a transmitter power exceeding 50 W PEP on the UHF 70 cm band from an area specified in § 2.106(c)(270)(i) of this chapter, unless expressly authorized by the FCC after mutual agreement, on a case-by-case basis, between the Regional Director of the applicable field facility and the military area frequency coordinator at the applicable military base.

(g) No station may transmit with a transmitter power exceeding 50 W PEP on the 33 cm band from within 241 km of the boundaries of the White Sands Missile Range. Its boundaries are those portions of Texas and New Mexico bounded on the south by latitude 31°41′ North, on the east by longitude 104°11′ West, on the north by latitude 34°30′ North, and on the west by longitude 107°30′ West.

(h) No station may transmit with a transmitter power exceeding 50 W PEP on the 219-220 MHz segment of the 1.25 m band.

(i) 60 m band power requirements: No station may transmit on the frequencies 5.332, 5.348, 5.373, and 5.405 MHz in the 60 m band with a radiated power exceeding 100 W ERP. No station may transmit in the 5.3515-5.3665 MHz band with a radiated power exceeding 9.15 W ERP. For the purpose of computing ERP, the transmitter PEP will be multiplied by the antenna gain relative to a half-wave dipole antenna. A half-wave dipole antenna will be presumed to have a gain of 1 (0 dBd). Licensees using other antennas must maintain in their station records either the antenna manufacturer's data on the antenna gain or calculations of the antenna gain.

(j) No station may transmit with a transmitter output exceeding 10 W PEP when the station is transmitting a SS emission type.

(k) No station may transmit in the 135.7-137.8 kHz (2200 m) band with a transmitter power exceeding 1.5 kW PEP or a radiated power exceeding 1 W EIRP.

(l) No station may transmit in the 472-479 kHz (630 m) band with a transmitter power exceeding 500 W PEP or a radiated power exceeding 5 W EIRP, except that in Alaska, stations located within 800 kilometers of the Russian Federation may not transmit with a radiated power exceeding 1 W EIRP.

(m) No station may transmit with a peak equivalent isotropically radiated power (EIRP) exceeding 316 W in the 76-81 GHz (4 mm) band.

eCFR text as of 1 Sep 2026 · read on ecfr.gov
Powerwerx SS-30DV 30A DC Power SupplySponsored · View on Amazon →RG-213 Coax Cable 75ft with PL259 ConnectorsSponsored · View on Amazon →
← G1B All groups G1D →